CCNP SWITCH 6.0 INSTRUCTOR LAB MANUAL PDF

CCNP SWITCH 6 – BitRadius. Instructor Lab Manual Book everyone. Download file Free Book PDF Ccnp Switch Instructor Lab Manual at. CCNP: Implementing Secure Converged Wide-area Networks v – Lab Copyright © Ensure that the switch is set up so that both the router and host are in the same. VLAN. .. Figure Internet Explorer Security Alert Prompt. ccnp switch instructor lab pdf. CCNP SWITCH Instructor Lab Manual. This document is exclusive property of Cisco Systems, Inc.

Author: Daizahn Brara
Country: Australia
Language: English (Spanish)
Genre: Life
Published (Last): 28 October 2006
Pages: 480
PDF File Size: 10.47 Mb
ePub File Size: 18.4 Mb
ISBN: 132-9-78602-605-9
Downloads: 41635
Price: Free* [*Free Regsitration Required]
Uploader: Mumi

Data cannot be sent or received over the port while it is in this state, but the switch can listen to BPDUs received on the port to detect a new root advertising itself.

swith To configure MST, first use the global configuration command spanning-tree mode mst on all four switches. D – down P – in port-channel I – stand-alone s – suspended H – Hot-standby LACP only R – Layer3 S – Layer2 U – in use f – failed to allocate aggregator u – unsuitable for bundling w – waiting to be aggregated d – default port Number of channel-groups in use: The other switches in the VTP domain can be configured as clients. The authentication portion of AAA requires a user to be identified before being allowed access to the network.

Instrjctor lab assumes the existence of fiber-optic gigabit ports, although this might not be the case with your lab equipment. Be sure to turn off debugging before continuing: Configure root guard on the root port that you found.

  HAIMABATI SEN PDF

Configure all inter-switch links statically as Remember me on this computer. Configure root guard on these ports to ensure that if a switch is added, it is not allowed to take over as root. Configure the host Cccnp settings. However, the VLAN database is still accessible for those who choose to use it. To verify the configuration, you can use the show interface summary, show wlan summary, and show run-config commands on the WLAN controller.

Configure the basic switch parameters and trunking. DHCP gives out dynamic IP addresses on a subnet to network devices or hosts rather than statically setting the addresses. The lab configuration files for the course should be in flash under the tshoot directory for a given.

Cisco Networking Academy, CCNP SWITCH Lab Manual, 2nd Edition | Pearson

Configure PortFast on an access port. This method assumes that each VLAN could be running inxtructor a differently shaped topology. The table does not include any other type of interface, even though a specific router might contain one.

The switch supports VLANs. However, if the show vlan command displays nondefault VLANs after you have deleted the vlan.

CCNP SWITCH Lab Manual, 2nd Edition

Use the show spanning-tree vlan 1 command on ALS2 to look for a root port. Configure trunks and EtherChannels between switches. The link providing the lowest root path cost was chosen as the active link. Then an agreement is established as to which links to keep active and which links to logically remove from the spanning tree disable if multiple links exist.

  KCET 28 TELETUBBIES PDF

Ccnp Tshoot Lab Manual Configuration Files – downloadsoftspecialists

The priority of the video traffic will be configured to be lower than the priority of the voice traffic. The pings from the student VLAN should fail. Enable spanning tree debugging on ALS1. Background IP phones have been deployed throughout the network.

Display the switch default VLAN information. The student and mnual VLANs should be listed in the output of this command.

The lab configuration files for the course should be in flash under the tshoot directory for a.

This is the result of the channel-group x mode being set to active. VLAN new root isa. Gateway show cdp neighbor detail Device ID: In either case, the network can be secured against switcn a disruption.

The following is a sample configuration for the VLAN subinterface. Configure the switch hostnames as shown in the topology.